homeasebo.blogg.se

1. Plunge mill pocket in mastercam x9 how to#
2. Plunge mill pocket in mastercam x9 code#
3. Plunge mill pocket in mastercam x9 plus#
4. Plunge mill pocket in mastercam x9 series#

We actually have hard edges to route from the machine path or the toolpath. “We build the structure as a wireframe and then extract the solid from that. “The nice thing about creating a solid model in SOLIDWORKS® and linking it in Mastercam is we know how we want it, so we can build it again,” said Kaspar. They built the part from the ground up, drafting a new solid model, verifying it, and sending it out for approvals. The Kormachine team worked together to reverse the dimensions, pulling them off as best they could because the original part was warped and cracked-bent and distressed in some places. Tolerances were a tight +/- 0.005 of an inch. The proprietary part measured 3 feet x 3 feet x 1 foot, consisting of a combination of Inconel, aluminum, stainless, and some copper brazing. The customer wanted to take an extension off the part and then build a new one from scratch. When an aerospace company delivered a part that needed to be reverse engineered to Waco, Texas-based Kormachine, owner/operator Colter Kaspar received no accompanying print, no solid model.

Plunge mill pocket in mastercam x9 series#

In FeatureCAM there is a setting along with a minimum ramp amount determined as a % of the cutter dia. Likely there is a setting in MC to tell it to force a linera ramp-on move. To date the only control I've ever seen that had no problem with ramping on an arc was the Brother Hs3100/3600 5100 control. 5005 dia hole accurately, all with a straight ramp to comp, arc-on path, arc-off path and linear ramp off comp.Īs to the second question, that might just be an inherited legacy fact that a comp-on and off must be done in a straight line.

To the first issue, the Haas G12/13 cycle is proof that a. Why does it need a straight line to turn on anyway? If youre trying to do a hole thats not much bigger than the cutter, i dont think youll have enough room to have a straight lead in to turn on the cutter comp.

Plunge mill pocket in mastercam x9 how to#

Good idea I just didnt know how to incorporate that into my existing program.

Plunge mill pocket in mastercam x9 code#

Luckily it wasn't too picky about where the g40 was put.ĭont they use I and J as kind of a newer style of programming? I wish my mastercam put out code using that so then I could have done what you said and just modify my finish pass I value because comp is always a pain. Then it alarmed out because I didnt end the tool comp so I had to put a g40 in my last line. It took me a while but I finally figured out where it would run it with out alarming out. I had to use a g41 in the start of a certain line, then a d2 at the end of that line.

Plunge mill pocket in mastercam x9 plus#

I know I could modify my mastercam program but I am not sure what all to take out, plus I am doing a roughing pass and a finish pass.īut I did manage to figure out the endmill comp. Thanks that would be a good but mastercam doesn't use the I and it would take me a while to write this program manually. Why? I have no idea.and half the time I'm in too much of a hurry to figure it out. Sometimes it is just a matter of changing the tool dia. by adjusting the wear offset without having to worry about all that cutter comp. Using this code, you can control your dia. Any reason this wont work or is a bad idea?ĭ = Tool Diameter Offset = Tool 1 Geometry Offset I don't get why it just doesn't turn on cutter comp when it picks the tool up and leave it on? I am thinking about reposting it with cutter comp off again and then just adding a g41 d2 right after g43 h2. Is there an easy way to make mastercam post this where my Haas TM1 will understand it? I was going to manually fix this in the program on the machine but it don't turn cutter comp on until the finish pass and it has posted a g41 several times. I tried running it but it alarms out saying it needs to turn on cutter comp with a linear move, not a circular move. Then on the tool offset page I put in a value of -.001 under diameter wear. So I reposted my program with cutter comp turned to wear on mastercam x. 709 round hole and it is coming out about. The latest and hopefully last problem is a cutter comp issue. Ok I am still working on the same parts I was a week ago and struggling to get them right but were slowly figuring our problems out one by one.